« previous next »
Pages: [1]

Author Topic: Quick Cam Timing Question  (Read 1142 times)

Offline Conker

  • I live here
  • *****
  • Posts: 1,999
Quick Cam Timing Question
« on: 22 February 2008, 22:45 »
I'm currently doing my head gasket, and while doing so noticed that the two dots on my cams are slightly off centre at TDC i.e. one is perfect, the other is slightly off. Here's a pic:



In the haynes, these are exactly in line. The question is, am I being too picky, or is the timing slightly out??

Logged

Offline rowlers

  • I live here
  • *****
  • Posts: 1,784
  • I'm back - MK7 GTI
Re: Quick Cam Timing Question
« Reply #1 on: 22 February 2008, 22:49 »
that looks good to me :wink:

wind the cams either way and they will line up. I've had my 16v cams one tooth out and it was way more notiecable than that!
Logged

Offline Mew

  • I live here
  • *****
  • Posts: 3,589
Re: Quick Cam Timing Question
« Reply #2 on: 22 February 2008, 22:55 »
Have you removed any of the bearing caps?
Logged

Offline Conker

  • I live here
  • *****
  • Posts: 1,999
Re: Quick Cam Timing Question
« Reply #3 on: 23 February 2008, 09:13 »
Quote from: Mew on 22 February 2008, 22:55
Have you removed any of the bearing caps?

What are they? (Sorry... I haven't got my manual on me)

Logged

Offline rowlers

  • I live here
  • *****
  • Posts: 1,784
  • I'm back - MK7 GTI
Re: Quick Cam Timing Question
« Reply #4 on: 23 February 2008, 09:46 »
the caps with 2 bolts on each that hold the cams down.

Those cams are aligned! :wink:
Logged

Offline Conker

  • I live here
  • *****
  • Posts: 1,999
Re: Quick Cam Timing Question
« Reply #5 on: 23 February 2008, 13:06 »
Quote from: rowlers on 23 February 2008, 09:46
the caps with 2 bolts on each that hold the cams down.

Those cams are aligned! :wink:

No I haven't removed them.

I guess its fine - Im so anal I should have been an aerospace engineer!

Logged

Offline russ-vdub

  • I live here
  • *****
  • Posts: 1,350
  • Once a Dub, Always a Dub
Re: Quick Cam Timing Question
« Reply #6 on: 24 February 2008, 18:08 »
surely if you are changing the head gasket you'll have to redo the timing anyways?
Logged

Offline JC

  • 10k hero
  • *
  • Posts: 13,429
  • Back in the North.
Re: Quick Cam Timing Question
« Reply #7 on: 24 February 2008, 18:30 »
Quote from: Conker on 23 February 2008, 13:06
Quote from: rowlers on 23 February 2008, 09:46
the caps with 2 bolts on each that hold the cams down.

Those cams are aligned! :wink:

No I haven't removed them.

I guess its fine - Im so anal I should have been an aerospace engineer!



oy oy  :shocked: :tongue:
Logged

Offline jammac

  • I live here
  • *****
  • Posts: 503
Re: Quick Cam Timing Question
« Reply #8 on: 24 February 2008, 20:48 »
Quote from: chuff on 24 February 2008, 18:30
Quote from: Conker on 23 February 2008, 13:06
Quote from: rowlers on 23 February 2008, 09:46
the caps with 2 bolts on each that hold the cams down.

Those cams are aligned! :wink:

No I haven't removed them.

I guess its fine - Im so anal I should have been an aerospace engineer!



oy oy  :shocked: :tongue:

did someone say anal?
Logged

ITS A TRAP!

Offline Dolly

  • I live here
  • *****
  • Posts: 721
Re: Quick Cam Timing Question
« Reply #9 on: 24 February 2008, 22:15 »
if you turn them, one will go clockwise, the other clockwise... apposed to getting further apart they wll get closer.. youll find its probably a nats, if they were a tooth out it would be blindingly obvious
Logged
Pages: [1]
« previous next »