« previous next »
Pages: [1]

Author Topic: mk3 8v misfire / 5K rev limit  (Read 1967 times)

Offline black90

  • GTI forum regular
  • ***
  • Posts: 237
mk3 8v misfire / 5K rev limit
« on: 12 March 2007, 09:59 »
Right I'm struggling here.

mk3 8v(ADY engine) has hesistant misfire and won't rev past 5000 revs.

Diagnostic revealed hall sender fault.
This looked to be because the distributor was in the wrong position.

Anyway, cambelt changed, all timed up correctly, and distributor back in correct position.
Fault code reset and the car was a different car for 2-3 miles.  Then back to the same problems.

Hall sender fault code had reappeared.

So I replaced the hall sender within the distributor.
Reset the fault code.
Again the car was alright for 1-2 miles then I can tell the car is back in limp mode.

Any ideas?

Thanks
Logged

Offline rubjonny

  • 10k hero
  • *
  • Posts: 16,349
  • Hello, my name is John and I'm a dub addict.
Re: mk3 8v misfire / 5K rev limit
« Reply #1 on: 12 March 2007, 12:29 »
timing still isnt right, try again ;)
Logged
Hello my name is John and I'm a dub addict.

Offline Len

  • 10k hero
  • *
  • Posts: 16,295
  • Guardian of the Seas, Protector of Waves
Re: mk3 8v misfire / 5K rev limit
« Reply #2 on: 12 March 2007, 12:47 »
Also might be worth doing an ECU reset by disconnecting the battery for 10/15 mins.

Once you have reset the timing properly first!
Logged
Mystic Blue Mk3 16v + Black Mk5 Gti 05 plate + Peugeot 405 Mi16

www.sas.org.uk
www.the-ace.org.uk

Offline black90

  • GTI forum regular
  • ***
  • Posts: 237
Re: mk3 8v misfire / 5K rev limit
« Reply #3 on: 12 March 2007, 12:47 »
Quote from: rubjonny on 12 March 2007, 12:29
timing still isnt right, try again ;)

Thanks but:

Camshaft gear arrow with the words O/T pointing to the arrow on the head with the words O/T.
Dot punch on flywheel in centre of flywheel inspection hole.
Centre of rotor arm pointing to notch on distributor housing.

What else?

 :smiley:

Logged

Offline rubjonny

  • 10k hero
  • *
  • Posts: 16,349
  • Hello, my name is John and I'm a dub addict.
Re: mk3 8v misfire / 5K rev limit
« Reply #4 on: 12 March 2007, 13:00 »
ok the only other thing I can think of is the crank sensor, if you have one.  Double check the timing though :)

afaik the dizzy on the ADY is not adjustible, so you might have to get it put on VAG COM to get the timing set...
« Last Edit: 12 March 2007, 13:02 by rubjonny »
Logged
Hello my name is John and I'm a dub addict.

Offline black90

  • GTI forum regular
  • ***
  • Posts: 237
Re: mk3 8v misfire / 5K rev limit
« Reply #5 on: 15 March 2007, 10:53 »

Double checked the timing last night.
It's correct as stated above.

The replacement hall sender had the pick-up at the opposite side of the distributor body(i.e. 180 degrees out)
Would this create an issue?
The literature that came with it said it would have no effect but I'm unsure???

Cheers
Logged

Offline rubjonny

  • 10k hero
  • *
  • Posts: 16,349
  • Hello, my name is John and I'm a dub addict.
Re: mk3 8v misfire / 5K rev limit
« Reply #6 on: 15 March 2007, 11:14 »
as long as the rotor arm is pointing to the TDC mark it should not matter.  I think you need to get it on VAG COM to get the timing setup.

As I said before I don't think the ADY dizzy should rotate, AFAIK its locked in position using a keyway?
Logged
Hello my name is John and I'm a dub addict.

Offline black90

  • GTI forum regular
  • ***
  • Posts: 237
Re: mk3 8v misfire / 5K rev limit
« Reply #7 on: 15 March 2007, 11:16 »
Quote from: rubjonny on 15 March 2007, 11:14
as long as the rotor arm is pointing to the TDC mark it should not matter.  I think you need to get it on VAG COM to get the timing setup.

As I said before I don't think the ADY dizzy should rotate, AFAIK its locked in position using a keyway?

Yes, 2 pins lock it in position either side of the bolt.

 
Logged
Pages: [1]
« previous next »