VagCom Help.....

[THiNK]

OK guys,

I pluged in my VagCom (Version 409.1), turned the key so all power was on, but not started.

Started VagCom,

Got the correct com post set and clicked 'Auto Scan'

I then selected

1J - VW G/J/B Mk4

And clicked start.

I went though a load of Baud rate tests then finished.

I'm guessing as nothign spectacluar happened then it hasn't run corrctly.

Can anyone provide any guidance?

Thanks,

CS

[Ridg]

it should query all the modules and then give you a report listing the errors if any

[cannybagatuda]

could be just hasnt found any faults?

[Ridg]

could be just hasnt found any faults?

no you should get something like

Friday,28,September,2007,20:27:10:26703
VAG-COM Version: Release 704.1
Data version: 20070723
Chassis Type: 1J - VW G/J/B Mk4
Scan: 01 02 03 08 15 16 17 19 22 29 35 36 37 39 46 47 55 56 57 75
          76
 
VIN: WVWXYZ   Mileage: 134770km/83742miles
-------------------------------------------------------------------------------
Address 01: Engine       Labels: None
   Part No: 038 906 019 HH
   Component: 1,9l R4 EDC G000SG  1491
   Coding: 00002
   Shop #: WSC 01271
   WVWXYZ     VWZ6Z0A4095961

No fault code found.
Readiness: 0 0 X X X

-------------------------------------------------------------------------------
Address 03: ABS Brakes       Labels: 1C0-907-37x-ASR.LBL
   Part No: 1C0 907 379 K
   Component: ASR FRONT MK60      0103
   Coding: 0021505
   Shop #: WSC 01271

No fault code found.

-------------------------------------------------------------------------------
Address 15: Airbags       Labels: 6Q0-909-605-VW5.LBL
   Part No: 1C0 909 605 A
   Component: 27 AIRBAG VW51 01   0004
   Coding: 12855
   Shop #: WSC 01271

No fault code found.

-------------------------------------------------------------------------------
Address 17: Instruments       Labels: 1J0-920-xx5-17.LBL
   Part No: 1J0 920 926 C
   Component: KOMBI+WEGFAHRS. RB8 V18
   Coding: 05414
   Shop #: WSC 00000
   WVWXYZ     VWZ6Z0A4095961

2 Faults Found:
01039 - Coolant Temperature Sensor (G2)
            30-10 - Open or Short to Plus - Intermittent
01176 - Key
            07-10 - Signal too Low - Intermittent

-------------------------------------------------------------------------------
Address 19: CAN Gateway       Labels: 6N0-909-901.LBL
   Part No: 6N0 909 901
   Component: Gateway K<->CAN    0001
   Coding: 00006
   Shop #: WSC 01271

No fault code found.

-------------------------------------------------------------------------------
Address 46: Central Conv.       Labels: 1C0-959-799.LBL
   Part No: 1C0 959 799 B
   Component: 1X Komfortgerát HLO  003
   Coding: 00258
   Shop #: WSC 01271

   Part No: 1C2959802A
   Component: 1X Tõrsteuer.FS KLO 0004

   Part No: 1C2959801A
   Component: 1X Tõrsteuer.BF KLO 0004

   Part No: 1C0959811A
   Component: 1X Tõrsteuer.HL KLO 0004

   Part No: 1C0959812A
   Component: 1X Tõrsteuer.HR KLO 0004

No fault code found.

-------------------------------------------------------------------------------
Address 55: Xenon Range       Labels: None
   Part No: 1J0 941 651
   Component: Leuchtweitenregel.  V07
   Coding: 00001
   Shop #: WSC 00000

No fault code found.

End   --------------------------------------------------------------------------------------------------
--------------------------------------------------------------------------------------------------------

[THiNK]

I defo don't get that lot!

It just done the scan through the numbers switching between screens then back to the first screen after you click scan.

CS

[THiNK]

Just ran it again and the same.

I have noticed you have a lot more channels to scan.

Scan: 01 02 03 08 15 16 17 19 22 29 35 36 37 39 46 47 55 56 57 75 76

Did you add these ?

Thanks,

CS

[Ridg]

Just ran it again and the same.

I have noticed you have a lot more channels to scan.

could be because mines the latest version and the full version

[THiNK]

hmm might have to invest then 

CS