« previous next »
Pages: [1] 2 3 4

Author Topic: how to replace a sill  (Read 4877 times)

Offline stainesy

  • I live here
  • *****
  • Posts: 3,442
  • im not a master debater but i'm a cunning linguist
how to replace a sill
« on: 31 July 2011, 18:22 »
Ok both my sills seem to be shot as front jacking points mangled totaly.
How do you remove and put on new sill?
I take it they are welded on?
Logged

Offline Wayne

  • Sir Postalot
  • *
  • Posts: 32,051
Re: how to replace a sill
« Reply #1 on: 31 July 2011, 19:10 »
Yep they are welded on.
Logged

Offline stainesy

  • I live here
  • *****
  • Posts: 3,442
  • im not a master debater but i'm a cunning linguist
Re: how to replace a sill
« Reply #2 on: 31 July 2011, 20:25 »
whats the going rate to have these replaced?
Logged

Offline Jack3559

  • I live here
  • *****
  • Posts: 2,301
Re: how to replace a sill
« Reply #3 on: 01 August 2011, 00:50 »
Very expensive.

To get mine done it came to £400 iirc.
Logged

Offline stainesy

  • I live here
  • *****
  • Posts: 3,442
  • im not a master debater but i'm a cunning linguist
Re: how to replace a sill
« Reply #4 on: 01 August 2011, 06:44 »
Quote from: Jack3559 on 01 August 2011, 00:50
Very expensive.

To get mine done it came to £400 iirc.
:shocked:
Logged

Offline Seanl

  • I live here
  • *****
  • Posts: 2,561
Re: how to replace a sill
« Reply #5 on: 01 August 2011, 09:32 »
I had one done at the last MOT on the drivers side. Cost £80
Logged
Classic Green Corrado VR6 Storm | Jetex Cat back | BMC CDA | VT mounts | Bilstein B12 | 288mm front brakes | Mk4 rear brakes | Goodridge braided hoses | BBS RX228s | Shortshifter | Lupo wipers | Uprated headlight loom | All red rears | Refreshed leather | Fresh paint |

Offline Jack3559

  • I live here
  • *****
  • Posts: 2,301
Re: how to replace a sill
« Reply #6 on: 01 August 2011, 12:21 »
Mine was a bit more than a sill though, it was seatbelt anchor points and stuff...
Logged

Offline Wayne

  • Sir Postalot
  • *
  • Posts: 32,051
Re: how to replace a sill
« Reply #7 on: 01 August 2011, 12:28 »
The problem comes after you cut the old sill off, you may get lucky and find nothing else but you may find the rust has spread.
Logged

Offline stainesy

  • I live here
  • *****
  • Posts: 3,442
  • im not a master debater but i'm a cunning linguist
Re: how to replace a sill
« Reply #8 on: 01 August 2011, 12:47 »
My sills are not rusty realy its just my front jacking points are mangled propper mangled.
And there is rust around front passenger side drainage hole thing. Got mot in a month.
Are they structural at all?
Logged

Offline Wayne

  • Sir Postalot
  • *
  • Posts: 32,051
Re: how to replace a sill
« Reply #9 on: 01 August 2011, 12:56 »
Quote from: stainesy on 01 August 2011, 12:47
Are they structural at all?

Yes they are  :smiley:
Logged
Pages: [1] 2 3 4
« previous next »