GolfGTIforum.co.uk
Model specific boards => Golf mk2 => Topic started by: bigman_10 on 09 August 2008, 15:50
-
first things first i'm gutted all the posts have been lost as i've lost my project thread :cry:! but it could be worse so thanks to jv for sorting things out :wink:
Anyway i've got standard seats in my 1.3 at the moment and they are very tired and all the foam bolsters in the back rest and the base are almost dead, coupling this with serious wear marks they're past there sell by!
so the quesion is what upgrades are possible? i was firstly thinking about the gti seats for the bucket seat type bolsters, then i got tempted by a few leather interiors for mk2s on the bay. but i know there are other possibilities like the corrado front seats with some minor mods to fit the rear bench? also the mk3 seats but the subframe has to be taken in 2 inches or something? what about the seat leon front seats? Any help welcome and minor/simple wleding work is not too much of a problem (well it shouldn't be unless my mate emigrates :grin:).
I'm not too bothered at the moment about having mathcing door cards and matching seats but obvously it would be a bonus! What do you rekon is a viable option??
thanks
(damm i've lost the sig aswell :laugh:)
-
i've had a search on the vw vortex and a bit more on here and the mk3 fronts seats dont actually need welding atall the foam can just be swapped over on the sub frames. would this be possible with the seat ibiza cupra seats below? i'm not sure if the back rest will slot into the mk2 base like the mk3 does?
-
SEAT ibiza seats will likely slot straight into your MK2, they're mostly based off the MK2 chassis. Failing that you can do a base swap. what year is your 1.3?
My mate has got Corrado seats in his MK2 and they're well nice!
-
Scirroco seats are a striaght swap too.
(http://i126.photobucket.com/albums/p89/bomp_bucket/Scirocco-fronts-02.jpg)
I think the MK1-3 Seat Ibiza fit straight in too, I'm looking for a lower 60/40 rearbench from a MK3 Ibiza GTi
like this.
(http://i126.photobucket.com/albums/p89/bomp_bucket/IbizaGtirearbench.jpg)
And the upper section of a Seat Toledo 60/40 rearbench like this.
(http://i126.photobucket.com/albums/p89/bomp_bucket/Seat-Tol-rearbench--armrest-01.jpg)
The Toledo seats from 1991 - 99 should fit ok.
-
your tilt knob is on the wrong side ;)
-
your tilt knob is on the wrong side ;)
Ha, never noticed that :grin:
-
or tis upside down, cant quite make it out :grin:
its a shame 99% of SEAT interiours are shockingly bad!
-
scirocco seats are what you want because they have such low subframes.
-
corrado ones too, plus they look nicer. however rocco seats can sometimes be found in a pattern that matches mk2 rear seats, so thats a plus. rado rear bench requires metal work to be fitted properly, or if you're really lucky you can find rado recaro seats in the blue stripe pattern as found on late spec mk2s. you can get mk3 seats in this pattern too
-
corrado ones too, plus they look nicer. however rocco seats can sometimes be found in a pattern that matches mk2 rear seats, so thats a plus. rado rear bench requires metal work to be fitted properly, or if you're really lucky you can find rado recaro seats in the blue stripe pattern as found on late spec mk2s. you can get mk3 seats in this pattern too
never realised corrado and scirocco seats shared subframes - thanks for the information. rear bench is not an issue as it will be getting lost.
-
I dont think the subframes are actually the same, but they are the same height :)
I always forget when i climb into my mates mk2 its quite a fall if you arn't prepared :grin:
edit: oh and another thing, if you have pre-90 MK2 GTI seats and want em lower without having to change/loose the std pattern, you can use a MK3 Polo GT/G40 (i.e. one with bolsters) driver seat base frame, it fits all the pre-90 MK2 fabric/foam perfectly and is lower :)
If you dont have bolsters a low spec Polo MK3 base will do, or you could get a low end spec seat and chop/weld your old bolster frame to it. Some late MK2 polo bases may work, but I think they have the forward/back handle on the wrong side a la MK1.
And make sure its a height adjustible frame, the non height adjust ones have the rear legs at the wrong angle to fit a MK2 well, I had one on my MK2 for a while (was from a LHD polo GTpassenger seat) I bent the legs so the seat would fit but it didnt slide in the rails very well.
-
Forgot to mention, that I swapped the stubby rocco tilt knobs for Golf MK2 ones, as they stick out further to hold the seat belts.
-
f you have pre-90 MK2 GTI seats and want em lower without having to change/loose the std pattern, you can use a MK3 Polo GT/G40 (i.e. one with bolsters) driver seat base frame, it fits all the pre-90 MK2 fabric/foam perfectly and is lower :)
Just to confuse things further, couldn't you use a scirocco frame with pre-90 mk2 foam and fabric?
-
noooooooooooooooooooooooooooooo
i is confused now
what seat / frame combo will get me LOWEST in the car - its a 90 spec 5 door as my heed hits the roof al the time :undecided:
-
Just to confuse things further, couldn't you use a scirocco frame with pre-90 mk2 foam and fabric?
No I dont think so, afaik all the rocco frames are different to MK2. Maybe MK1 rocco?
noooooooooooooooooooooooooooooo
i is confused now
what seat / frame combo will get me LOWEST in the car - its a 90 spec 5 door as my heed hits the roof al the time :undecided:
If you want to keep your oem seats youre out of luck! if you dont mind swapping then Scirocco or Corrado seats, or pre-90 MK2 seats with Polo MK3 base frame :)