Now if i only had my insurance sorted DOH! :embarassed:
I would see if sundaydriver was free to see if we could set this up differently,
Especially as he said he is coming to my neck of the woods to my local dealer for a look at the VWR wheels.
DOH!
http://forums.vwvortex.com/zerothread?id=4743553&page=1VAGCOM
These instructions apply to Golf 6 platform vehicles including the Golf and Jetta. Ross-Tech is not responsible for any damage or problems that may result from following these instructions. They are to be used at your own risk.
It is always recommended to perform a complete Auto-Scan and save it prior to coding changes. Please see the Online Demo / Manual: Auto Scan Screen
Address 09 - Central Electronics:
If this module does not communicate, unlock all vehicle doors and try again.
Windows up via remote
Comfort Operation (via Remote Control) found in Adaptation. From the drop down list, choose 1 (On) and Save.
Daytime Running Lights are found in Coding, Long Coding helper, the lamp systems are different:
- Factory Xenon – Byte 11
- Factory Halogen – Byte 15
Cornering Lights via Front Fog Lights active are found in Coding, Long Coding helper
Fogs as Daytime Running Lights Tested on Xenon equipped vehicles
Fogs only
Byte 11 - un-check "Daytime Running Lights (via Low Beam) active"
Byte 14, Bit 1 - Manually modify the binary value from a "0" to a "1"
Fogs and Xenon Headlights as DRLs at the same time
Byte 11 - leave this alone
Byte 14, Bit 1 - Manually modify the binary value from a "0" to a "1"
Fogs as Daytime Running Lights suggestion for Halogen equipped vehicles, NOT TESTED
If this is successful on Halogen vehicles please update this thread.
Disable Factory Halogen DRL's in Byte 15 - un-check "Daytime Running Lights (via separate lights) active"
Byte 14, Bit 1 - Manually modify the binary value from a "0" to a "1"
Alarm Confirmation via lights and horn
Found in Coding, Long Coding helper.
Comfort Turn signals
Found in Adaptation. From the drop down list, choose the number of flashes and Save.
Emergency Brake Warning active
This actually uses the 4 ways flashers, not a flashing of the brake lamps.
Found in Coding, Long Coding helper.
Auto-Lock
Found in Coding, Long Coding helper.
Coming Home
Found in Coding, Long Coding helper.
If the vehicle is not equipped with an "Auto" headlight switch, coming home activation will likely require you to pull the high beam
stalk back briefly after shutting the vehicle off and before exiting. The description should be found in your owners manual.
Leaving Home
Found in Coding, Long Coding helper.
Leaving home will likely require the "Auto" switch and a light sensor. The description should be found in your owners manual.
Address 08 – Auto HVAC:
Drivers heated seat memory
Found in Adaptation. From the drop down list, choose Storage of seat heater level driver. Change to On and Save.
This may not be supported on all control modules.
Address 17 – Instruments:
Staging feedback here:
MkVI Instrument cluster - which one do you have?
Please update that thread with your info. It looks like 5K6 920 870 D and 5K6 920 970 H will activate.
Retrofits:
NAR Vehicle, European switch retrofit:
DIY - Wiring a Euro Headlight Switch to run parking lights
NAR Golf / Gti LED Tail Light retrofit:
In progress...
LED tail lights
You need vagcom to reprogram. I´m sure your lokal dealer can help you.
Set your new code in BYTE 18 to:
Byte 18 Bit 2
04 = 00000100
I´m not sure this will make you remove your errors, because cars whitout xenon and prductionsweek before week 45 2009 has a different software. This software can not be reprogrammed, need to change your hardware BCM.
Maybee you can find an answer in this thread
Speedo needles
VCDS Version 912 beta
Select under 17 Instruments -> 10 adaption -> Staging
and activate.
Thats it.
