« previous next »
Pages: [1]

Author Topic: Camber, camber shims, and all that  (Read 1112 times)

Offline Mikester

  • Forum addict
  • *
  • Posts: 6,427
  • Civic Type R
Camber, camber shims, and all that
« on: 15 July 2009, 23:50 »
I know what camber is, but i dont know how is set, the parts involved etc.

Im having my rear arches rolled, then im thinking about going down on the front, and getting the rear having a little bit of camber.

I know this will do the tyre wear in uneven, but i dont mind.

But how do i go about this? Ive heard the words "camber shims" dont know what they are though.

What can i do?
Logged

Offline boneybradley

  • Forum Supporter
  • Serious forum addict
  • *****
  • Posts: 9,482
  • Back in a Mk3...
Re: Camber, camber shims, and all that
« Reply #1 on: 15 July 2009, 23:52 »
bloody scene queen!  :grin: :grin:

but check dickies guide http://www.golfgtiforum.co.uk/index.php?topic=88044.0  :wink:
Logged
Moderator of The Dub-Tug Squad!! (What some call the MK3 section!)



Full range of quality parts for your Volkswagen available at Oemandmore.co.uk

Offline Mikester

  • Forum addict
  • *
  • Posts: 6,427
  • Civic Type R
Re: Camber, camber shims, and all that
« Reply #2 on: 15 July 2009, 23:55 »
lol. Cheers mate.

I tell you what, i have only been into the vw scene for like 2 years, but im transforming at an alarming rate. lol.
Logged

Offline Mikester

  • Forum addict
  • *
  • Posts: 6,427
  • Civic Type R
Re: Camber, camber shims, and all that
« Reply #3 on: 16 July 2009, 00:12 »
Might go for this much camber. :laugh:

Logged

Offline Wayne

  • Sir Postalot
  • *
  • Posts: 32,051
Re: Camber, camber shims, and all that
« Reply #4 on: 16 July 2009, 00:25 »
I have seen people make their own, easy enough to do.
Logged

Offline bored_Welsh_lad

  • I live here
  • *****
  • Posts: 1,425
Re: Camber, camber shims, and all that
« Reply #5 on: 16 July 2009, 06:57 »
Quote from: Wayne on 16 July 2009, 00:25
I have seen people make their own, easy enough to do.

Washers...
Logged
Mk3 Golf Gti:Full Milltek system and Decat,K&N filter,mk2 Cam,-1.5 degree camber shims, borbet a's, toyo proxies,hot tuning coils, brembo vented discs, greenstuff pads...Soon to have Eaton Power

mk3 16v 5dr Gti,mintex extreme pads,drilled/grooved discs,lowered,cat back powerflow system,omp panel filter with modified airbox,debadged grill, started prep for spraying, lots to come :D

Bumper Vents :D

Offline LazyLunatic

  • Forum addict
  • *
  • Posts: 4,153
  • MK3 20VT Project
Re: Camber, camber shims, and all that
« Reply #6 on: 16 July 2009, 08:08 »
front, under the two bolts holding the hub to the coilover, push the hubs in and up as much as possible and do the bolts back up. you will see what i mean by in and up when you do it. gives you a fair amount of camber on the fronts, but beware the tyre wear lol! :D
Logged
Pages: [1]
« previous next »