GolfGTIforum.co.uk

Model specific boards => Golf mk3 => Topic started by: greendragon on 12 September 2008, 14:19

Title: were shud these wires connect 2
Post by: greendragon on 12 September 2008, 14:19: were shud this brown wire and a yellow wire connect 2 its on the same bit of loom the clips on 2 the throttle body
(http://img.photobucket.com/albums/v335/phyllip/golf001.jpg)
Title: Re: were shud these wires connect 2
Post by: Rmachines on 12 September 2008, 16:17: Not sure but if you look to the middle left bottom of the picture it looks like there is a conector which has no plug? mabbey it went there?
Title: Re: were shud these wires connect 2
Post by: Horney on 12 September 2008, 16:37: Is this a VR6?

nick
Title: Re: were shud these wires connect 2
Post by: greendragon on 12 September 2008, 16:56: yes it is 1993 vr6
Title: Re: were shud these wires connect 2
Post by: davero on 12 September 2008, 22:04: Will have a look at mine tomorrow and see if i can find out for you.
Title: Re: were shud these wires connect 2
Post by: greendragon on 12 September 2008, 23:51: thanks
Title: Re: were shud these wires connect 2
Post by: boneybradley on 13 September 2008, 00:27: If you dont get sorted..try this link for a pdf vr6 wiring diagram http://volkswagen.msk.ru/electro/g3/g3_wd22_aaa.pdf (http://volkswagen.msk.ru/electro/g3/g3_wd22_aaa.pdf)
Title: Re: were shud these wires connect 2
Post by: davero on 13 September 2008, 09:44: As Rmachines said there is a plug going to the empty connector on the picture. This is where those wires go on mine(1996 vr6)
Title: Re: were shud these wires connect 2
Post by: greendragon on 13 September 2008, 12:55: so as its empty i can just tape um up ?????
Title: Re: were shud these wires connect 2
Post by: davero on 13 September 2008, 14:55: Mine has a plug attached to it, and the plug is connected to the grey sensor in your picture.
Title: Re: were shud these wires connect 2
Post by: jamie16v on 13 September 2008, 18:11: diagnostic use of some sort?..
Title: Re: were shud these wires connect 2
Post by: beccasmk3gti on 14 September 2008, 08:57: Quote from: dave16v on 13 September 2008, 14:55
Mine has a plug attached to it, and the plug is connected to the grey sensor in your picture.

car doesnt run properly if this is not connected i tried it on mine a 1996 vr6 and runs poor
Title: Re: were shud these wires connect 2
Post by: LazyLunatic on 14 September 2008, 09:40: Find a vr6 that is breaking or go to scrappy and see if you can get the loom.
Is this only on the vr6 or can it found on other models?
Get the plug and solder the wires to the wires on the new plug. Then plug it in!

LL ;)
Title: Re: were shud these wires connect 2
Post by: beccasmk3gti on 14 September 2008, 09:43: vr6 only its part of the rocker breather system
Title: Re: were shud these wires connect 2
Post by: greendragon on 14 September 2008, 16:41: thats wird cus the plug just clips in but theres nufink that the wires wod do cus it just a blanck plug
Title: Re: were shud these wires connect 2
Post by: Rmachines on 14 September 2008, 22:23: my 16v ABF engine has this but im pretty sure its not a blank, mabey they share the same loom?
Title: Re: were shud these wires connect 2
Post by: jafo on 15 September 2008, 16:28: Yep iv def got this plug with wires on my vr because i can remember taking it all apart to clean the inside of the pipe.