GolfGTIforum.co.uk
Model specific boards => Golf mk2 => Topic started by: caddyrage on 21 April 2007, 13:25
-
can someone please post a pic of the relay layout on the fuse panel of an 87-89 mk2 gti 8v with the PB digifant engine. Redoing the wiring on my caddy after the last loom melted :rolleyes: and dont know if i'am missing a relay.
Also can someone tell me where these wires go?
(http://i91.photobucket.com/albums/k314/caddyrage/SSA50453.jpg)
These are at the fuse box side of the loom
Just wanna get the loom sorted once and for all this time
Cheers, lee
-
anyone?
-
check my fusebox FAQ in the garage section for relay layouts, as for those wires you've got an earth there (brown/white) at least but I'm not sure about the other 3, can you see where they have come from?
-
The bro/red wire goes to a 2 pin white plug which connects to the ecu loom. A bla/yel wire on the same white plug goes to position R on the fuse box which is a 2 pin green plug.
The red/whi wire goes to a black 2 pin plug which also connects to the ecu loom, a red/yel is the other wire on that plug.
The black 2 pin plug in the pic, the whi/red goes to what looks like the air temp sensor and the gre/bla wire goes to a position on above the oil filter, must be a sender of some sort.
hope you can help matey
-
right!
1. I think this runs to pin D/2, according to my fusebox FAQ?
2. Still not sure about that one, any idea where on the ecu plug it goes?
3. Looks like the oil temp sender & outside air temp wires, I think they should plug into another plug from the dash clock loom :)
-
Just traced wires back using a spare loom.
the brown/red wire goes to position 1mon the ecu plug
the red/white goes nowhere, just buried in insulation for no reason.
the black plug was'nt fitted when i ran the 2L in my caddy(thought i'd sort it properly this time).
so then, its just the brown/red to sort hopefully :smiley:
-
here we go, from my FAQ:
C
18- red/blk- thermo switch for cold start valve (K-Jet f/inj) or digifant ECU pin 1
Red/white is probably for the lambda probe if one is fitted, theres a random cut red/white wire in my Digifant loom as well :)
As for the black/green wire, I believe on your car it should run to pin 3 of the 6 pin plug, and the red/white wire should run to pin 2 of the 6 pin plug of the dash clocks :)
-
Right, so you think it be good to go then if i placed the bro/red wire in position C 18?.
edit...
just looked at the C plug on my original caddy loom and the PB loom i have and there's no wire in that position so will it be fine as obviously it was'nt that position on the mk2 gti the loom came from :huh:
-
hmm, are you sure that wire is in pin 1?
Edit: there should defo be a wire in position C18...
-
C18 must of been the position i removed a wire for the bullet connector to redo the fuel pump positive wire :rolleyes: . Will connect it up and let ya know how i get on. Cheers mate
-
well i've connected the wires as they should be but all i'am getting is the engine turning over. I dont here the fuel pump working either so am i missing something?
Edit...
these are the relays fitted, are they correct?
1. 32
2. 80
8. 18
10. 19
12. 21
Add on location as a 42
-
ok there should be a jumper wire between R/1 and D/2, do you have that?
-
Yep, got that mate