GolfGTIforum.co.uk
Model specific boards => Golf mk7 => Topic started by: Hurdy on 18 June 2018, 11:56
-
Well, I’m back.
After selling my beloved 6R and a year or so in the wilderness in a Seat Leon Cupra I am finally back to the fold with a shiny new 7.5R.
Spec of the new arrival is:-
5dr DSG.
Deep Pearl Black
Titan Black Vienna Leather with heated front seats
19” Pretoria Black alloys
90% rear tinted glass
LED headlights with Dynamic headlight assist
Discover Navigation Pro
Dynaudio Excite soundpack
KESSY
DCC
Panoramic sunroof
lane assist with Dynamic light assist including TSR
Winter Pack
Already have some aftermarket parts to go on the car:-
19x8.5” ET45 Team Dynamics Pro Race 1.3 in gloss black with Michelin Pilot Sport 4S tyres.
Brembo 4 pot calipers with Vagbremtechnic caliper adapters, Brembo pads, HEL braided lines, Clubsport S discs, RS3 Vented dust shields and RS3 brake ducts.
Revo lower engine mount and full REVO engine and transmission mounts.
Wagner intercooler
Forge Carbon intake and intake pipe
CTS 90 degree intake pipe and muffler delete.
CTS discharge pipe
CTS throttle pipe
REVO Scorpion 3” downpipe and decat section ( although may go with 200 cell race cat)
Tuning will be through Statller, who use ETuners mapping for the engine and DSG.
parts on the list to get are:-
Catback exhaust system - although it may end up as a full system as I will probably go for a 3.5” downpipe.
Big turbo kit. This will either be a TTE, Turbo Technics or EFR...haven’t made my mind up fully yet.
Lowering will be Racingline springs as I have DCC.
Rear ARB upgrade.
Maybe WMI but haven’t made my mind up yet.
carbon mirror caps
some kind of splitter
a rear spoiler extension.
-
Welcome back John. I see by the list you have'nt changed.
-
Congrats, sounds like someone's been into the MK7 tuning scene a lot :tongue: If I a may ask, are you tuning it for drag racing? track? or just private use? Any particular power goals? Up to 500bhp I think your mods list is ok as is but above that you're starting to look at reinforcing the motor imo.
I only got a few remarks: if you intend to track the car I'd definitely avoid the CSS discs and instead complement the 4pots with a set that has proper, symmetrical cooling (I'd also avoid drilled designs). For the rest of the parts that are already here (there) I assume they were on your Cupra and will be just transferred to the R?
Also curious as to why you want to change the Pretorias with those TD 1.3's. Looks wise there's nothing that comes even close to Prets on a 7/7.5 R or CS and if my sources are right about the TD's they are ~2kg heavier per wheel (9.6 vs 11.5)?
Re the turbo options, I'd also consider the LM500 v2 from Germany. Decent price, upgraded core and plug n play solution (IS38 housing) with very good results so far (again assuming you are aiming the 500bhp mark and not much above that).
You should definitely keep us posted with updates! :wink:
-
Welcome back, the Mk6 was a beast. Looking forward to reading the build thread.
-
Look forward to seeing you rather well dressed at a drag strip in the future
-
Nice blacked out spec! Sounds like it will be awesome. I'm Sheffield based by will keep an eye out if you're around (assuming as you are using Statler - they are good guys, only used them for servicing on a Porsche but Steve seemed sound).
-
Welcome back John. I see by the list you have'nt changed.
LOL, never will.
-
Congrats, sounds like someone's been into the MK7 tuning scene a lot :tongue: If I a may ask, are you tuning it for drag racing? track? or just private use? Any particular power goals? Up to 500bhp I think your mods list is ok as is but above that you're starting to look at reinforcing the motor imo.
I only got a few remarks: if you intend to track the car I'd definitely avoid the CSS discs and instead complement the 4pots with a set that has proper, symmetrical cooling (I'd also avoid drilled designs). For the rest of the parts that are already here (there) I assume they were on your Cupra and will be just transferred to the R?
Also curious as to why you want to change the Pretorias with those TD 1.3's. Looks wise there's nothing that comes even close to Prets on a 7/7.5 R or CS and if my sources are right about the TD's they are ~2kg heavier per wheel (9.6 vs 11.5)?
Re the turbo options, I'd also consider the LM500 v2 from Germany. Decent price, upgraded core and plug n play solution (IS38 housing) with very good results so far (again assuming you are aiming the 500bhp mark and not much above that).
You should definitely keep us posted with updates! :wink:
I’ve been in the MKV, MKVI and MKVII tuning scene and do a little drag racing and track work.
Most of the kit I have is a hand over from the Cupra.
Ultimately the mods will develop further, but the parts I have now will go on to start with. In the past I have had AP racing two piece 362mm discs with project Mu pads and 8 pots along with A8 rear discs.
For power fuelling will need injectors, HPFP and LPFP uprating. The target is not fixed, but definitely over 500bhp. There are several cars around that have lasted well over 500bhp and over a year. Generally boost kept at under 2 bar is the level where the TSI has long term longevity.
The Prets are lovely, but the 1.3’s are stronger and will be used for day to day duties. I have five sets of alloys, from lightweight Oz Ultraleggeras through to TDPR 1.2’s as well as Hoosier drag radials and so I’m pretty much covered in the wheel dept.
As for the turbo choice the LM500 V2 is a good shout and another to consider. 😎👍
My previous motors all had experimental mods on them from Nitrous to Owen Development turbos and hybrids, so in not afraid to test new mods. It should be a fun ride. 😋
-
I’ve been in the MKV, MKVI and MKVII tuning scene and do a little drag racing and track work.
Most of the kit I have is a hand over from the Cupra.
Ultimately the mods will develop further, but the parts I have now will go on to start with. In the past I have had AP racing two piece 362mm discs with project Mu pads and 8 pots along with A8 rear discs.
For power fuelling will need injectors, HPFP and LPFP uprating. The target is not fixed, but definitely over 500bhp. There are several cars around that have lasted well over 500bhp and over a year. Generally boost kept at under 2 bar is the level where the TSI has long term longevity.
The Prets are lovely, but the 1.3’s are stronger and will be used for day to day duties. I have five sets of alloys, from lightweight Oz Ultraleggeras through to TDPR 1.2’s as well as Hoosier drag radials and so I’m pretty much covered in the wheel dept.
As for the turbo choice the LM500 V2 is a good shout and another to consider. 😎👍
My previous motors all had experimental mods on them from Nitrous to Owen Development turbos and hybrids, so in not afraid to test new mods. It should be a fun ride. 😋
Agreed on the fueling and yes, several cars near the 500bhp mark have been fine with basically just a BT and supporting peripherals, it's when you go over 550 where typically another "wave" of upgrades is needed from what I've seen but wasn't sure where you're aiming. I see you're spoiled for choice on rims, that's never bad a thing :tongue:
Wait, you didn't happen to run a twincharger Polo GTI several years back?? Username tells me something...
-
I’m pretty sure you were floating around when I got my mk5 back in 2007??
-
I’m pretty sure you were floating around when I got my mk5 back in 2007??
I think Hurdy only ever floats in the queue for a 1/4 mile, other than that usually a blur.
-
I had a ride along in his Polo GTI.. That was mental. But for me the Edition 30 he built... :whistle:
-
Yes, the Polo GTI on WMI and hybrid turbo was mine. The ED30 on twin bottle Nitrous was mine and the 500+bhp Golf6R on BT kit and WMI was mine too! 😋😱😜
-
What about the Lexus?
Good to see you back :cool:
-
What about the Lexus?
Good to see you back :cool:
Hurdy the Alan Partridge years
-
What about the Lexus?
Good to see you back :cool:
Don’t mention the L word!
I get a nervous twitch about it now! :laugh:
-
Hurdy, Not sure if I heard right but are you working at Statlers?
-
If he is, then he needs to answer the bloody phone. :laugh:
Good to see you back again. I'll keep my eyes peeled around town for a roaring R. :cool:
-
Hurdy, Not sure if I heard right but are you working at Statlers?
I was but I’m now looking after the Ikea building in Sheffield. :cool: