GolfGTIforum.co.uk
Model specific boards => Golf mk4 => Topic started by: dane on 02 June 2013, 00:16
-
Hi iv just got a intercooler for my golf but pipes don't fit nicely can anyone give me a list of every bend and pipe I need please because I don't have a clue what I'm looking for ha :grin:
-
1x 45mm straight silicone (100mm)
1x 45 x 63mm alloy reducer
2x 63mm silicone bend
1x 63mm alloy 45* bend
1x 8mm alloy joiner (welded onto 45* for n75)
1x 25mm alloy joiner (welded onto 45* for d/v)
1x 63mm 45* silicone bend
1x 63mm straight alloy (100mm long)
1x 63mm alloy bend
1x 76 x 63mm silicone red. bend
1x 76 x 63 silicone 45* red. bend
1x 63mm straight alloy (200mm long)
1x 63mm 135* silicone bend
1x 63mm forge MAP pipe (or 100mm straight alloy)
2x 45 x 60mm s/steel clamps
2x 70 x 90mm s/steel clamps
12x 60 x 80mm s/steel clamps
1x Front mount intercooler TYPE B 600x300x76MM
Taken from my build thread :wink:
-
Thanks mate but some of the pipes don't have the degree on your list would that matter dane
-
how much did all that cost you rio?.. without the intercooler!! :smiley:
-
1x 45mm straight silicone (100mm)
1x 45 x 63mm alloy reducer
2x 63mm silicone bend
1x 63mm alloy 45* bend
1x 8mm alloy joiner (welded onto 45* for n75)
1x 25mm alloy joiner (welded onto 45* for d/v)
1x 63mm 45* silicone bend
1x 63mm straight alloy (100mm long)
1x 63mm alloy bend
1x 76 x 63mm silicone red. bend
1x 76 x 63 silicone 45* red. bend
1x 63mm straight alloy (200mm long)
1x 63mm 135* silicone bend
1x 63mm forge MAP pipe (or 100mm straight alloy)
2x 45 x 60mm s/steel clamps
2x 70 x 90mm s/steel clamps
12x 60 x 80mm s/steel clamps
1x Front mount intercooler TYPE B 600x300x76MM
Taken from my build thread :wink:
Look at the star next to some of the numbers ever tried to use a degree symbol on a computer or a phone for that matter I don't even know where one is and putting a * is quicker than writing degree :laugh:
-
how much did all that cost you rio?.. without the intercooler!! :smiley:
About £200 I think for the pipe work :wink:
-
Yea I know the * is for degree but a cuple of them just say alloy or silicon bend it don't say what bend mate any chance of letting me know what degree they are thanks
-
Bend without any number is a 90* bend mate :smiley:
-
Thanks mate and where is best to get it all iv got a kit from toyosport and they said its all 2.5 pipes after fitting it I relied its 2" ha and it all is hanging out and bumper didn't go back on right so I'm not to good at getting things so more help and advise I can get the better thanks again rio
-
Check my project thread page 3 or 4 I think
Most pipes bought from ASH (auto silicone hoses)
-
also out of interest, sorry to thread hijack...
but anyone know the pipe I need...
I basically had to use a straight and bend it into a 90 deg bend, but its obviously very restrictive.
its the pipe you can see in rio's sig pic, the one in the bottom left corner...
am I right in thinking its a 63mm diameter 90degree bend? and one got any links?
-
Would it be same pipe kit for a 550x140x65 intercooler mate
-
also out of interest, sorry to thread hijack...
but anyone know the pipe I need...
I basically had to use a straight and bend it into a 90 deg bend, but its obviously very restrictive.
its the pipe you can see in rio's sig pic, the one in the bottom left corner...
am I right in thinking its a 63mm diameter 90degree bend? and one got any links?
That is part of the forge 5 piece boost hose kit but sure you could get it separately
151054297579 eBay no check it out
Would it be same pipe kit for a 550x140x65 intercooler mate
What is the inlet/outlet size on that cooler??
-
64mm but iv got to get 2.5 pipes so I can remap so r tech told me
-
So get all that's on the list but Insted of
1x 76 x 63mm silicone red. bend
1x 76 x 63 silicone 45* red. bend
Just get then as 63mm (not reducing bends)
-
Ok well do and where did you get 45 to 63 alloy bit from and hat laugh it need to been and where did you get the 8mm bit for n75 to and the clamps mate can't find that lot ha
-
http://www.ebay.co.uk/sch/autoperformanceonline/m.html?_nkw=&_armrs=1&_from=&_ipg=&_trksid=p3686
try here..
http://www.ebay.co.uk/sch/m.html?_odkw=&_osacat=0&_armrs=1&_ssn=autoperformanceonline&_trksid=p2046732.m570.l1313.TR0.TRC0&_nkw=8mm+alloy&_sacat=0&_from=R40
-
Everything other then that reducer was from ash/ap motorstore and the reducer was just from the bay
Jamie's got the right idea!!!
-
Last bit any chance of letting me know what's for hot side and what's for cold just I'm thinking of doing it my self mate and thanks for everything
-
Tbh the list is in order from turbo to manifold so the red. Bends are on the cooler so u should be able to tell from there pal :wink:
-
Your a legend mate now just to order it up and get it welded then fit it ill pm you if I get stuck thanks with there was a way to rate ppl for there help dane
-
No worries, yeah do that always happy to help :wink: