GolfGTIforum.co.uk
Model specific boards => Golf mk4 => Topic started by: rench on 06 April 2012, 18:02
-
just had this fitted on my anni and not sure if it looks to big, what you guys think?
(http://i1227.photobucket.com/albums/ee429/rench3/02bdb04f.jpg)
(http://i1227.photobucket.com/albums/ee429/rench3/3f7d1522.jpg)
-
Way OTT just being honest.
-
:sick: toooo big.. belongs on a civic.. should have gone for anni style tip thats i did and looks perfect with rear anni valance :wink:
-
yea think im gonna have to get next size down 3.5 or 3 going to look better?
-
yea think im gonna have to get next size down
this :cool:
-
this what lol?
-
next size down :wink:
-
Tut tut at your illegal number plate :wink:
Yeah got a size smaller mate, will look loads better.
-
3.5 will look ok?
-
3.5 will look ok?
I would say that would be ideal :smiley:
What size it that one?
-
3.5 will look ok?
I would say that would be ideal :smiley:
What size it that one?
looks about 4.5-5 inch
-
Whent for the 4inch same as the milltek I had but with it been rolled out it looks huge lol just hope it's not going to cost a stupid amount to swap tip
-
Whent for the 4inch same as the milltek I had but with it been rolled out it looks huge lol just hope it's not going to cost a stupid amount to swap tip
May be a idea to see an example before you decide on the next size :smiley:
-
Whent for the 4inch same as the milltek I had but with it been rolled out it looks huge lol just hope it's not going to cost a stupid amount to swap tip
May be a idea to see an example before you decide on the next size :smiley:
wish i had done this when i got the subaru 1 done at 5inch :grin: :grin: wasnt quiet either
-
Yea, though as the milltek was 4 and that looked ok id get away with it but obviously not.
-
bit too big mate.
-
bit too big mate.
Girls keep telling me that all the time...
-
3.5 or 4 inch slash cut rolled in look the best
-
bit too big mate.
Girls keep telling me that all the time...
liar :grin: :grin:
-
heres a pic of mine it is a 3.5" inrolled anni tip.. think may be 3" not actully sure :lipsrsealed: buts its the same as anniversary tip :grin:
(http://i253.photobucket.com/albums/hh60/naveedali1/Image0131.jpg)
-
Can you find out what size yours is still going for rolled out but needs to go smaller
-
I think looks ok fills hole up anyway. When I take my crappy milltek rubbish exh off going twin 3.5" . Can you tell I hate milltek!!!! Get pipewerx custom made jobbie next, milltek waste of my hard earned cash.
-
just confirmed mine is 3.5" rolled in .. if your going to have it rolled out still may look too big.. go 3.25" if going rolled out
-
I think it looks nice I personally like the rolled out edge and size looks good
-
I think looks ok fills hole up anyway. When I take my crappy milltek rubbish exh off going twin 3.5" . Can you tell I hate milltek!!!! Get pipewerx custom made jobbie next, milltek waste of my hard earned cash.
is it discreet ? am after a discreet backbox :wink: :smiley:
-
barry, you had a 5inch on anni bumper? get a pick of that up mate
-
barry, you had a 5inch on anni bumper? get a pick of that up mate
on a scoob mate sorry if u miss understood me :smiley: or didnt read my post right
-
i think it looks big but not ott if your happy then thats all that matters different is good some times could be worse lol
-
I think it's a little to big, I think with a 3.5 in will look alot better then
-
heres a pic of mine it is a 3.5" inrolled anni tip.. think may be 3" not actully sure :lipsrsealed: buts its the same as anniversary tip :grin:
(http://i253.photobucket.com/albums/hh60/naveedali1/Image0131.jpg)
this is wot i have on mine.
-
F%ck em be different :grin:
-
£40 to change tip
-
£40 to change tip
:cool: What are you going for then?
-
Going to look at a 3 or 3.5 rolled out see which looks best
-
sell me the exhaust pal when you get the smaller one
-
It's only the tip Im getting changed unless you want the full exhaust pm me if so pal