Author Topic: Where have all the Mk3s gone?!  (Read 7130 times)

Offline Mr_Orange

  • I live here
  • *****
  • Posts: 2,192
  • MK4 GTi Turbo Exclusive 150 AUM
Re: Where have all the Mk3s gone?!
« Reply #10 on: 25 July 2021, 09:14 »
That red 16v doesn't look far off. I'd suggest to bypass the immo and get it back on the road as is  :wink:
My MK4 was living in the garage and looking tired, but I got it MOTd and back on the road for fear of losing the love for it. I'll be taking it out for a blast this morning.
My brother is on the look out for a mk3 again. He's been through a few, and broke a nice one for a brief stint in a MK2. His last one had a full respray, air ride and every rare bolt on he could get his hands on. I think he regrets letting it go, but didn't lose out after selling on all the toys. Certainly looking at some serious money for the next one.


Build thread clicky

Offline itavaltalainen

  • I live here
  • *****
  • Posts: 2,687
  • VCDS and VCP - fault codes, coding, VIM activation
Re: Where have all the Mk3s gone?!
« Reply #11 on: 29 July 2021, 15:39 »
The immo on those is easy.
And relatively cheap to fix as well.
Easiest to buy a 2nd hand immo box with the same p/n that comes with the pin.
Then all you need is vcds, box with unknown pin is tricky but doable if it comes with a transponder that is matched to it.

I'd expect fixing would cost <£100, an immo delete won't cost significantly less.
2019 Seat Leon ST FR DSG 135kW - eclipse orange - 23k miles

Offline WeekendMechanic

  • Here all the time
  • ****
  • Posts: 305
  • Golf MK3 GTD
Re: Where have all the Mk3s gone?!
« Reply #12 on: 31 August 2021, 17:57 »
The immo on those is easy.
And relatively cheap to fix as well.
Easiest to buy a 2nd hand immo box with the same p/n that comes with the pin.
Then all you need is vcds, box with unknown pin is tricky but doable if it comes with a transponder that is matched to it.

I'd expect fixing would cost <£100, an immo delete won't cost significantly less.

I`m glad you brought this up I know you need a pin to program with vcds,
I just bought a Vag-Can cable so as to extract the pin from mine I`m assuming the transponder and box are matched.
I've been doing some research some say Vag-Can, can dump the code, others say only external EEPROM reader can do it.
Maybe you can help us both out...
I`m still waiting for cable in the mail.


Offline itavaltalainen

  • I live here
  • *****
  • Posts: 2,687
  • VCDS and VCP - fault codes, coding, VIM activation
Re: Where have all the Mk3s gone?!
« Reply #13 on: 08 September 2021, 22:42 »
Send me a private message.
Can't be done with an eeprom reader, needs a little more involved kit (mcu reader, these don't use external eeprom) or via obd if you got a matched key.
2019 Seat Leon ST FR DSG 135kW - eclipse orange - 23k miles

Offline pfnsht

  • Just got here
  • *
  • Posts: 6
Re: Where have all the Mk3s gone?!
« Reply #14 on: 28 September 2021, 19:40 »
I'm still going on the mk3. I could have MOTd and got it out but when I get going perfecting I can't stop! I've sorted the side you see in the photo interms of welding and paint under the trims but the drivers side was a bit worse - needs a new rear arch and has had patches on the sill in the past - i'm probably going to get a pro to do the arch and and new sill on that side.

Once i am done the body work i will move on to fitting the bilsteins and will refurb the calipers and fit new bearings and wishbones etc. Then MOT and I'll get the panels that need painting done.

If I buy project cars again (probably) they have to be MOTd as it would have been nice to get it driving and bonding with it on the road.

I have bought some 7j RX226 for it to keep the motivation as have left it for a few months over summer whilst I enjoyed driving my corrado.


Offline WeekendMechanic

  • Here all the time
  • ****
  • Posts: 305
  • Golf MK3 GTD
Re: Where have all the Mk3s gone?!
« Reply #15 on: 06 October 2021, 08:57 »
You should do everything yourself.
You can still find whole rear mud guard panels.
Cut what you need from them and weld them.
You can even paint it yourself ,yes the cost of buying proper tools to do this stuff outweighs the cost of getting someone to do them but over time if you keep this hobby they will pay for themselves.